wildscience :: Home :: Products :: SUBJECT :: Physics :: Rocket Ball Launch Lab

Facebook

Rocket Ball Launch Lab
Unique and mind boggling. Multiple award winning kit explores energy and ballistics. Make your own launchers and watch the Rocket Balls actually bounce MUCH higher than you drop them! Enough stuff for several more stunts and tricks you can try.

Age Grading: 8+ Years
Product Code: WS/01L

    ¡@¡@¡@
¡@¡@¡@
VIDEO
FAQ
Q1. So what results should we get from each of the Tests 1 to 4 , and Why?

A1. A: Firstly - you need to practice and practice to get the best results. We suggest dropping the balls next to a wall. And then move 'sticky paper notes' up the wall to show the highest point of flight of the small ball. Have a competition! When there is no improvement in height, that becomes your 'optimum maximum¡¦. Do it for each of the tests below. BUT predict how high the top ball will go BEFORE you do the actual dropping and measuring. This is real science.

TEST 1 (page 10)
What happens: the small ball flies away really fast. And much higher than it was dropped!
Why: Because all the other balls push their kinetic or moving energy into it.

TEST 2 (page 11)
Now the second smallest ball is at the end of the stick.
What happens: The second smallest ball doesn¡¦t fly away as fast!
Why: Because the second smallest ball has a bigger mass, and the total energy supplied from the balls below is less, it doesn¡¦t fly up so high.

TEST 3 (page 11)
Now we have only two balls ¡V the biggest and the smallest.
What happens: The smaller ball flies away, but slower than in Test 1 and 2 because there is less energy below the top ball than in any other setup.

TEST 4
Now we are just missing one ball.
What happens: the smallest top ball still flies higher than it was dropped because it now has the energy from the two larger balls below it. But not as high as in Test 1! Less balls, less overall kinetic ( moving energy).



Q2. We bought last xmas hyper launcher rocket ball factory and I want to buy some of the refill crystals. Where can I buy these from?

A2. We are not allowed to sell refills alone for our kits without also adding in all sorts of protective gear. And that makes it too expensive.

The crystal are very specific to this kit and - and sorry again - we don't think you cant find them anywhere else. However you can by the Rocket Ball kit or Hyperlauncher on line or at other stores. But yes - you'll end up with extra sets of moulds and goggles.

We thank you for being a WILD! Scientist and hope this information helps you decide what to do next.



Q3. The granules stuck to the moulds and the hyperlauncher balls didn't come out

A3.

SOLUTION 1: The best hyperlauncher balls are made by very tightly packing the moulds. Loose packed granules tend not to stick to each other so well and may stick to the mould. Also grip the mould halves tightly under the water. They do swell, and do try to push the mould apart. This is all good for making hyper bouncy balls.

SOLUTION 2: Smear cooking oil around the inside of the mould. Very little is needed, or it interferes with the water permeation. Then, when the balls are ready for use, a smear of oil on the stick shaft helps reduce friction. Ideally we do not use oil as if it is misapplied it can 'disable' water access to the granules.





Q4. If you forgot to keeping bouncy balls in a plastic bag in the fridge and the balls went hard!!

A4.

Now, we have managed to revive some of our rock hard balls that seem to hide in the corners Dr WILD's lab!
Try soaking them in a glass of cold water in the fridge for a while. Depending on how hard the balls are - this may take an hour or two or a day. The aim is to re-gel the crystals both in the exterior and interior of the ball. But not to dissolve the crystals. Squeeze them every now and then until you can feel elasticity has returned. Then leave them out for the surface only to dry so it is not tacky. Then try using them again.
Don't use hot water or they quickly get coated with a slimy sort of glue - which in itself is totally harmless and very interesting : it is the polymer dissolving. But the balls will stick together when bounced. If they have been totally dried out for a long time, sorry ... they do tend to stay as rocks with a gluggy exterior after long soaking.





Q5. The balls didn't bounce as expected!

A5.

These are some possibilities that might solve the query :

1. Maybe she is dropping them onto a bouncy wooden or lino/vinyl floor. We need to use very solid, very hard surface: eg concrete or ceramic tiles, or the energy in the balls is dissipated.

2. It takes practice to let the assembly slip from the fingers and fall totally vertically. A few degrees off vertical and a lot of energy is lost. So keep practicing. When you get it just right - get ready for a mind boggling surprise.

3. Maybe they are still sticky when she is dropping the assembly. Most of the balls' energy will be lost trying to pull themselves free. So let the surface dry enough so they don't stick together when pushed together by hand. NOTE - please store them in a plastic bag in the fridge so they stay bouncy. Totally dry balls go hard as rocks and also don't bounce.

4. Loose bits of granules around the 'collars' of the balls reduce the energy transfer efficiency from ball to ball. Snip off ragged bits with sharp scissors if they wont come off with a spoon.





Back
Home  |  Products  |  News  |  About Us  |  Awards  |  Schools  |  Global Challenge  |  Parents  |  Games  |  FAQ  |  Distributor  |  Contact Us
WILD! Science™ and bubble device is a registered trademark of Kinlea Holdings Pty Ltd ACN 128 972 903.
Copyright © Kinlea Holdings Pty Ltd, 2012. All rights reserved.